
Custom Metal Buildings: Design-to-Delivery Timeline, Phase by Phase

A custom red iron metal building takes about a week to quote and 8 to 16 weeks to deliver, depending on its size and design complexity. Engineering starts from your jobsite address. Permits, the foundation, and erection run on your side of the schedule, so start those the day the stamped drawings arrive.
Custom metal buildings can take almost any size, door layout, or color. The calendar is less flexible. On a red iron (welded I-beam) building, the schedule runs in seven phases. Here's how a typical project runs, who owns each phase, and what you need on hand to keep it moving. Width and use come first, since engineering can't start without them, so if those are still open, size the building by its use before you plan the calendar.
What Makes a Metal Building "Custom" at ProSpan?
Every building we sell is engineered to its jobsite address and intended use, including wind and snow loads. That's the custom part, and it's why a red iron quote can't come out of a price calculator.
Inside that engineering, you choose the geometry:
- Width: clear spans up to 250 feet, meaning no interior columns across the full width
- Eave height: 10 to 30+ feet, measured at the outside wall where the roof meets it
- Bay spacing: typically 20 to 25 feet between frames
- Roof pitch: 2:12 or 4:12 standard, others on request
- Roof style: gable or single-slope standard; monitor and offset ridge for agricultural, aviation, or retail buildings
Then come the finish choices: door and window frame-outs, insulation from R-10 to R-25 (banded systems for R-30 and up), and galvalume or one of 20+ colors in 26-gauge. Each choice feeds the engineering, which is why the order you make them in affects the schedule.
This is what a pre engineered metal building (PEMB) means in practice. The system is standardized, the building is not.
How Long Does a Custom Metal Building Take, Start to Finish?
Timing is approximate and varies by building and jurisdiction.
| Phase | Approximate timing | Who owns it | What you walk away with |
|---|---|---|---|
| 1. Scope call | Week 1 | You and your ProSpan rep | Use, size, site address, door locations |
| 2. Engineered quote | 3 to 7 days after scope | Your ProSpan rep | A quote engineered to your site |
| 3. Order and options | As fast as you settle the options | You and your rep | Locked size, doors, insulation, color |
| 4. Stamped drawings | After the order | Your ProSpan rep | Permit-ready, engineer-stamped structural and foundation plans |
| 5. Permit and foundation | Varies by jurisdiction | You, your architect, your contractor | Permit and a cured foundation |
| 6. Fabrication and delivery | 8 to 16 weeks, by size and design complexity | Your ProSpan rep | The building package on your site |
| 7. Erection | Depends on size, crew, and site | Erection number on request (local FL/GA jobs) or your contractor | A standing building |
Phases 5 and 6 overlap. That overlap is the whole game: the permit and the foundation should finish while the steel is being fabricated, not after it lands.
Week 1: What Happens Before You Get a Quote?
The first call is a scope conversation. Your rep needs four things to send your project to engineering:
- What the building is for. A hangar, an equipment barn, a warehouse, and a municipal building carry different loads and door needs.
- Width, length, and eave height. Rough numbers are fine. If you don't have them, our standard sizes are a good starting point.
- The jobsite address. Wind and snow design start here.
- Large door locations. Big openings change the framing, so they belong in the first conversation.
From there, each red iron quote takes 3 to 7 days of engineering time. That's slower than a tube-steel price tool, and it's the reason the number holds up.
On wind design, the rep pulls information from state requirements for wind speeds. It's the responsibility of you or your architect to verify the local wind speed design requirements. Do that during this week, not after the order. It's also why we don't quote one flat wind rating: how hurricane resistant a red iron building is depends on the engineering for its site.
After the Quote: How Do You Lock In the Design?
It's tempting to rush this phase, but a change made later costs more time than one made now. Before you sign, settle:
- Doors and windows. Frame-outs are part of the building package, so moving a door after the drawings are stamped can mean new engineering.
- Insulation. It's ordered with the package, so pick the R-value and system now. Fiberglass insulation runs from R-10 to R-25, with banded systems for R-30 and up.
- Galvalume or color. Galvalume and color are priced differently. Switching from one color to another doesn't change the price, but switching between galvalume and color does. Pick from the color options before you sign.
- Financing, if you need it. GreenSky consumer financing is available up to $100,000 for qualified individuals. There's no rent-to-own on red iron.
Your ProSpan rep will walk you through what's needed to place the order.
When Do the Stamped Drawings Arrive, and What Do You Do With Them?
Your building package includes permit-ready, engineer-stamped drawings and stamped foundation plans. Foundation engineering is available when required.
Once the drawings are in hand, two clocks start on your side:
- The permit. You or your contractor typically submit the stamped drawings to your local building department. Review times vary widely by jurisdiction, so call the permit office early and ask what they need.
- The foundation. Your concrete contractor builds to the stamped foundation plans. The concrete has to cure before steel goes up. Under OSHA's steel erection standard, the erector needs written notice that footings and walls have reached 75 percent of design strength, or enough strength to carry erection loads, before erection starts.
Contractors: this is where schedules slip. Get the stamped drawings to the permit office and the concrete crew the same week.
The 8-to-16-Week Window: What Happens During Fabrication and Delivery?
Lead times for delivery run 8 to 16 weeks, depending on size and design complexity. A smaller building with standard doors tends to sit toward the short end. A wide-span hangar with a large door opening or an industrial steel building with heavy framing tends to sit toward the long end.
The package ships anywhere in the continental US. What arrives on the truck:
- Primary and secondary framing
- Roof and wall panels, trim, and fasteners
- Bracing
- Your stamped structural and foundation plans (already in hand by now)
Delivery isn't included in the building price, so ask how it's quoted for your site. Before the truck shows up, confirm the delivery date with your rep, and agree with your erector where the bundles will be staged and what equipment will be on site to unload them.
Who Erects the Building, and How Long Does That Take?
Installation isn't included in the price of a ProSpan building. We sell the engineered building package. Erection is a separate step, and who does it depends on where you're building:
- Florida and Georgia: For local Florida and Georgia jobs, ask your rep for an erection number when you request a quote. It's priced separately.
- Everywhere else in the continental US: We ship the package and stamped drawings, and your contractor erects the building. If you don't have an erector yet, tell your rep, and we can try to provide a contact.
The crew stands the primary frames, sets purlins and girts, installs insulation, then hangs panels and trim. How long that takes depends on the building's size, the crew, the equipment on site, and the weather, so ask your erector for a duration once the drawings are in hand.
What Slows a Custom Metal Building Down?
Schedules usually slip on decisions, not fabrication:
- Late wind verification. If the local wind requirement differs from the state figure the quote used, the engineering has to be redone.
- Door changes after drawings. A new opening can mean new framing and new engineering.
- The foundation isn't ready. Steel that arrives before the concrete has cured waits on site.
- Permit questions nobody answered. A plan reviewer's comment can sit for weeks if no one owns the reply. That's you, your architect, or your contractor.
- Undecided options. Insulation, color, and frame-outs all need to be settled before the order.
The fix for every one of these is the same: make the decisions in the first two phases, and start the permit and foundation the moment the drawings land.
What Should Contractors Build Into Their Schedule?
For a GC running a warehouse steel building or commercial job, treat the red iron package as a long-lead item, like switchgear. A few habits keep it on track:
- Get a jobsite address and door schedule to us before anything else.
- Have the architect verify local wind and snow design while the quote is in engineering.
- Book the concrete sub against the stamped foundation plans, not against the delivery date.
- Line up the erector and the crane well before delivery. Outside Florida and Georgia, that's your crew.
The Metal Building Manufacturers Association publishes design and erection resources for metal building systems that are worth having on hand. Larger jobs can start from a common commercial red iron building configuration.
Frequently Asked Questions
How long from quote to delivery for a custom metal building?
The engineered quote takes 3 to 7 days. Delivery lead times run 8 to 16 weeks, depending on the building's size and design complexity. Permits, the foundation, and erection add time on your side of the schedule.
Is installation included in the price of a custom metal building?
No. ProSpan sells the engineered building package, and delivery and installation are not included in the price. For local jobs in Florida and Georgia, you can ask for a separate erection number. Elsewhere, your contractor erects the building.
Who submits the building permit?
You or your contractor typically do. Your building package includes permit-ready, engineer-stamped drawings and stamped foundation plans to submit to your local building department.
Who verifies the wind design for my site?
The rep pulls information from state requirements for wind speeds. It's the responsibility of you or your architect to verify the local wind speed design requirements before you order.
Can I finance a custom metal building?
Yes, for qualified individuals. GreenSky consumer financing is available up to $100,000. Rent-to-own isn't offered on red iron buildings.
Start Your Timeline With a Quote
The clock starts with a jobsite address. Send us what the building is for, the rough size, where the big doors go, and where it's going, and we'll start engineering. Still pricing? Compare what a 40x60 red iron building costs and check what ships in a building package before you call.
Request a quote or call (386) 247-0255 (toll-free (855) 493-0332), Monday to Friday, 9:00am to 5:00pm.


